PPG INDUSTRIES INC COATINGS & RESINS GROUP -- 90-374 PITT-TECH GLOSS WHITE -- 8010-00F045309 
=====================  Product Identification  =====================

Product ID:90-374 PITT-TECH GLOSS WHITE
MSDS Date:02/24/1997
FSC:8010
NIIN:00F045309
=== Responsible Party ===
Company Name:PPG INDUSTRIES INC COATINGS & RESINS GROUP
Address:4325 ROSANNA DR
Box:9
City:ALLISON PARK
State:PA
ZIP:15101-5000
Country:US
Info Phone Num:412-492-5555/304-843-1300
Emergency Phone Num:304-843-1300/412-492-5555
CAGE:DO542
=== Contractor Identification ===
Company Name:PPG INDUSTRIES INC. COATINGS & RESINS GP
Address:4325 ROSEANNA DR PO BOX 9
Box:9
City:ALLISON PARK
State:PA
ZIP:15101
Phone:412-492-5555
CAGE:DO542
Company Name:PPG INDUSTRIES, EAST POINT
Box:UNKNOW
CAGE:PPIND

=============  Composition/Information on Ingredients  =============

Ingred Name:TITANIUM DIOXIDE, TITANIUM OXIDE  (SUSPECTED ANIMAL
    CARCINOGEN, IARC GROUP 3)	*97-2*
CAS:13463-67-7
RTECS #:XR2275000
Fraction by Wt: 10-20%
OSHA PEL:10 MG/CUM
ACGIH TLV:10 MG/CUM (DUST)

Ingred Name:1-(2-BUTOXY-1-METHYLETHOXY)-2-PROPANOL,  DIPROPYLENE GLYCOL
    MONOBUTYL ETHER	   *97-2*
CAS:29911-28-2
Fraction by Wt: 1-5%

Ingred Name:DIETHYLENE GLYCOL METHYL ETHER, 2-(2-METHOXYETHOXY) ETHANOL
    METHYL CARBITOL
CAS:111-77-3
RTECS #:KL6125000
Fraction by Wt: 1-5%
OSHA PEL:50 PPM
ACGIH TLV:25 PPM

Ingred Name:2-(2-BUTOXYETHYOXY)-ETHANOL, DIETHYLENE GLYCOL MONOBUTYL
    ETHER (BUTYL CARBITOL)	   *97-2*
CAS:112-34-5
RTECS #:KJ9100000
Fraction by Wt: 1-5%

=====================  Hazards Identification  =====================

Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:INHALATION/INGESTION: HARMFUL. EYES:
    MAY CAUSE SEVERE IRRITATION. SKIN: MAY CAUSE SLIGHT IRRITATION.
    PRODUCT CONTAINS AN ETHYLENE SERIES GLYCOL ETHER &/ACETATE WHICH
    CAUSES ADVERSE EFFECTS ON KIDNEYS,	LIVER, BLOOD &/BLOOD-FORMING
    TISSUE.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:IRRITATION.

=======================  First Aid Measures  =======================

First Aid:INGESTION: DON'T INDUCE VOMITING. GENTLY WIPE OUT INSIDE OF
    MOUTH TO REMOVE ANY RESIDUAL MATERIAL. EYES: REMOVE CONTACT LENSES
    & FLUSH W/GENTLE STREAM OF LUKE WARM WATER FOR 15 MINS. SKIN: FLUSH
    W/PLE NTY OF WATER FOR 15 MINS FOLLOWED BY WASHING W/SOAP & WATER.
    INHALATION: REMOVE TO FRESH AIR. GIVE CPR & OTHER SUPPORT MEASURES
    AS REQUIRED. OBTAIN MEDICAL ATTENTION IN ALL CASES.

=====================  Fire Fighting Measures  =====================

Extinguishing Media:USE MEDIA APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:WEAR A SCBA & FULL PROTECTIVE CLOTHING. WATER
    SPRAY MAY BE INEFFECTIVE BUT MAY BE USED TO COOL CLOSED CONTAINERS.
    IF WATER IS USED, FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:INVISIBLE VAPORS CAN TRAVEL TO IGNITION
    SOURCE & FLASH BACK. CLOSED CONTAINERS MAY EXPLODE WHEN OVERHEATED.

==================  Accidental Release Measures  ==================

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ISOLATE AREA.
    REMOVE IGNITION SOURCES. TAKE UP MATERIAL W/SAND, VERMICULITE/OTHER
    NONCOMBUSTIBLE ABSORBENT MATERIAL & PLACE IN CLEAN, EMPTY
    CONTAINERS FOR DISPOSAL. ONLY M ATERIAL & ABSORBENT SHOULD BE
    PLACED INCONTAINER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:DON'T STORE >120F. KEEP AWAY FROM
    IGNITION SOURCES. GROUND CONTAINERS WHEN POURING. AVOID FREE FALL
    OF LIQUIDS IN EXCESS OF A FEW INCHES.
Other Precautions:DON'T SMOKE WHILE USING THIS PRODUCT. KEEP CONTAINERS
    TIGHTLY CLOSED WHEN NOT IN USE. DON'T APPLY TO HOT SURFACES. IF
    PART OF A MULTIPLE COMPONENT SYSTEM, READ OTHER MSDS BEFORE
    BLENDING AS RESULTING  MIXTURE MAY HAVE HAZARDS OF ALL PARTS.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:WEAR A NIOSH APPROVED AIR PURIFYING RESPIRATOR
    W/APPROPRIATE CHEMICAL CARTRIDGES/POSITIVE PRESSURE AIR SUPPLIED
    RESPIRATOR WHERE VENTILATION IS INADEQUATE.
Ventilation:GENERAL DILUTION/LOCAL EXHAUST IN VOLUME & PATTERN TO KEEP
    CONCENTRATION OF CONTAMINANTS 1
Spec Gravity:1.2
Evaporation Rate & Reference:(BU O AC =100): 32
Solubility in Water:62.5%
Appearance and Odor:VISCOUS LIQUID W/CHARACTERISTIC SOLVENT ODOR.
Percent Volatiles by Volume:63.76

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG ALKALIES, STRONG MINERAL ACIDS, STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXTREME HEAT, SPARKS, FLAME & OTHER
    IGNITION SOURCES.
Hazardous Decomposition Products:BY EXPOSURE TO EXTREME HEAT: CO, CO2,
    OXIDES OF ALUMINUM, LOWER MOLECULAR WEIGHT POLYMER FRACTIONS.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF IAW/FEDERAL, STATE & LOCAL
    REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED/DISPOSED OF
    THROUGH AN APPROVED WASTE MANAGEMENT FACILITY.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.